HNPoolSolo SHA-256 Mining Pool
Coins / Bitcoin
BTC

Bitcoin BTC

SHA-256 · reward 3.125 BTC · block target 10.0 minutes
soon node not responding
Hashrate pool
0 H/s
0 workers · 0 addresses
Block height
—
last block —
Next block difficulty
0
network hashrate 0 H/s
Est. time to block
—
odds per day —

24-hour charts

Network hashrate

Belum cukup data untuk grafik — dashboard mengumpulkan samples every 60 seconds; the chart appears after 2 samples (about 2 minutes).

Difficulty blok berikutnya

Belum cukup data untuk grafik — dashboard mengumpulkan samples every 60 seconds; the chart appears after 2 samples (about 2 minutes).

24-hour pool hashrate

Belum cukup data untuk grafik — dashboard mengumpulkan samples every 60 seconds; the chart appears after 2 samples (about 2 minutes).

Status pool

Shares accepted
—
cumulative since the pool started
Shares rejected
—
stale or below-target-difficulty shares
Best share
0
vs difficulty 0
Pool uptime
—
pool.status missing

Connected miners

AddressRig1m1 hr ShareBestLast share
No miners have connected to this coin yet.

Blocks found yet?

Blocks you find are paid by the node straight to your address in the coinbase, so the proof lives on the blockchain, not in the pool database. Look up your address in this coin's explorer to see its history.

Operational notes

Rejected shares are usually stale shares right after a new block arrives, or shares below the target difficulty for large rigs. If the miner keeps disconnecting, check connectivity to - and make sure it is reachable from the miner's network.

Miner setup guide

1 · Connect your miner

Pool address (stratum)
The stratum endpoint for this coin is not active yet — the node is still finishing its initial block download (IBD).
Username—
Passwordx  (anything works)
AlgorithmSHA-256
Modesolo — full reward to the block finder
Address formatbech32 (bc1...) atau base58
Address example—
Pool coinbase tag—
Recommended walletBitcoin Core / Sparrow / Electrum
The BTC stratum endpoint is not open yet.

2 · Per-device guide

Bitaxe · NerdQAxe (AxeOS)

  1. Open the miner web UI (its IP address), go to the Settings → Pool tab.
  2. Fill in the Stratum URL and Port exactly as in the connection box above.
  3. Set Username = your wallet address, optionally with .namarig.
  4. Password = x. Save — the miner restarts on its own.

Antminer · WhatsMiner · Avalon

  1. Log in to the miner panel → Miner Configuration / Pool Settings.
  2. Pool 1 URL: the stratum address above. Pool 2 can be set as a backup.
  3. Worker: wallet address .namarig. Password is up to you.
  4. Save, then restart the miner.

NerdMiner / ESP32 lottery

  1. Open the config portal (usually 192.168.4.1 while pairing).
  2. Choose coin BTC, then fill in the pool host and port.
  3. Set the wallet/username to your wallet address.
  4. A low hashrate is normal — it is a lottery ticket after all.

cgminer / bfgminer (CLI)

Endpoint not active yet.

Quick connection test:

3 · Check your miner

Once your miner submits its first share, its stats appear here. Open the address detail page to see per-rig hashrate, best share, and block-finding odds.

The BTC node is still in initial sync (IBD) — when this config was written it was ~4.5% done (350k of 966k blocks) at ~53 blocks/min.
Preparation before opening BTC: raise par to 4 and dbcache to ~250, add pool-specific rpcuser/rpcpassword, add zmqpubhashblock, then run a third ckpool instance on its own port.
BTC difficulty is extremely high — with Bitaxe-level hashrate the odds are measured in years, not days.